zyxel_gs1920_series

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Next revision
Previous revision
zyxel_gs1920_series [2020/10/20 19:41]
svanheule Create page with overview table
zyxel_gs1920_series [2021/01/01 21:44] (current)
svanheule [GS1920-24HP] Correct RTL8231 addressing
Line 3: Line 3:
 The GS1920 series is a line of managed gigabit ethernet switches. Two revisions exist, but both are built with Realtek hardware. The GS1920 series is a line of managed gigabit ethernet switches. Two revisions exist, but both are built with Realtek hardware.
  
-^ Switch name ^ RJ45 ports ^ Combo SFP ports ^ Dedicated SFP ports ^ PoE ports ^ +^ Switch name ^ RJ45 ports ^ Combo SFP ports ^ Dedicated SFP ports ^ PoE ports ^ SoC 
-| GS1920-24 | 28 | 4 | - | - | +| GS1920-24 | 28 | 4 | - | - | RTL8392M 
-| GS1920-24HP | 28 | 4 | - | 24 | +| GS1920-24HP | 28 | 4 | - | 24 | RTL8392M 
-| GS1920-48 | 48 | 4 | 2 | - | +| GS1920-48 | 48 | 4 | 2 | - | RTL8393M 
-| GS1920-48HP | 48 | 4 | 2 | 48 | +| GS1920-48HP | 48 | 4 | 2 | 48 | RTL8393M 
-| GS1920-8HPv2 | 10 | 2 | - | 8 | +| GS1920-8HPv2 | 10 | 2 | - | 8 | RTL8391M 
-| GS1920-24v2 | 28 | 4 | - | - | +| GS1920-24v2 | 28 | 4 | - | - | RTL8391M 
-| GS1920-24HPv2 | 28 | 4 | - | +| GS1920-24HPv2 | 28 | 4 | - | 24 | RTL8391M 
-| GS1920-48v2 | 48 | 4 | 2 | - | +| GS1920-48v2 | 48 | 4 | 2 | - | RTL8393M 
-| GS1920-48HPv2 | 48 | 4 | 2 | 48 |+| GS1920-48HPv2 | 48 | 4 | 2 | 48 | RTL8393M |
  
 +===== Models =====
 +==== GS1920-24HP ====
 +=== Hardware ===
 +  * SoC: RTL839x
 +  * Ethernet:
 +    * 3× RTL8218 (to be confirmed)
 +    * 1× RTL???? (combo ports)
 +  * RAM: Nanya NT5CB64M16FP-DH, 128MiB DDR3
 +  * Flash: Macronix MX25L1283F, 16MiB SPI NOR
 +  * PoE controller: STM32F100
 +  * PoE PSE: 6× BCM59111
 +  * GPIO:
 +    * 1× [[RTL8231]] as GPIO expander: MII mode, device address 0x3
 +    * 3× RTL8231 as shift register: port status LEDs
 +    * HC164 shift register for device status LEDs
 +  * ADT7468 (I2C/SMBus) thermal controller with 3× 3-pin fan
 +  * Sipex SP3232 RS-232 transceiver
  
 +The serial port header J2 uses the standard [[https://en.wikipedia.org/wiki/Serial_port#Pinouts|DCE pinout]], with TX/RX on pins 2 and 3, and ground on pin 5. Port settings are 9600 baud, 8n1, with ±5.6V logic levels.
 +
 +The PoE management MCU and the ADT7468 fan controller are on a shared I2C bus. The PoE MCU is at address 0x20, while the fan controller is at (fixed) address 0x2E.
 +
 +=== Photos ===
 +^ Board ^ Pictures ^
 +| Overview | {{:wiki:zyxel:gs1920-24hp-front.jpg?200|device front}} {{:wiki:zyxel:gs1920-24hp-overview.jpg?200|inside overview}} |
 +| Main board | {{:wiki:zyxel:gs1920-24hp-main.jpg?200|main board overview}} {{:wiki:zyxel:gs1920-24hp-main-soc-memory.jpg?200|main board SoC and memory}} {{:wiki:zyxel:gs1920-24hp-main-gpio.jpg?200|main board GPIOs}} {{:wiki:zyxel:gs1920-24hp-main-fan.jpg?200|main board fan control}} {{:wiki:zyxel:gs1920-24hp-main-serial-sfp.jpg?200|main board serial port and SFP cages}} {{:wiki:zyxel:gs1920-24hp-main-back.jpg?200|main board backside}} |
 +| PoE daughter board | {{:wiki:zyxel:gs1920-24hp-poe.jpg?200|PoE board}}  {{:wiki:zyxel:gs1920-24hp-poe-detail.jpg?200|PoE controller ICs}} {{:wiki:zyxel:gs1920-24hp-poe-back.jpg?200|PoE board backside}}  |
  • zyxel_gs1920_series.1603222908.txt.gz
  • Last modified: 2020/10/20 19:41
  • by svanheule