software:broadcom_poe_control_protocol

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
Last revision Both sides next revision
software:broadcom_poe_control_protocol [2020/11/18 10:04]
svanheule [Set device power management] rename disconnect
software:broadcom_poe_control_protocol [2020/11/20 14:01]
svanheule [Set classification enable]
Line 49: Line 49:
 | ''0e'' | [[#Set port to PSE output mapping]] || | ''0e'' | [[#Set port to PSE output mapping]] ||
 | ''10'' | [[#Set detection type]] || | ''10'' | [[#Set detection type]] ||
 +| ''11'' | [[#Set classification enable]] ||
 | ''13'' | [[#Set disconnect type]] || | ''13'' | [[#Set disconnect type]] ||
 | ''15'' | [[#Set port power limit type]] || | ''15'' | [[#Set port power limit type]] ||
Line 210: Line 211:
 | port | 1 | Port index number. Use ''7f'' to configure all ports with one command. | | port | 1 | Port index number. Use ''7f'' to configure all ports with one command. |
 | detection_type | 1 | ''00'': No detection \\ ''01'': Legacy \\ ''02'': IEEE 802.3af 4-point detection (default) \\ ''03'': 4-point detection, followed by legacy \\ ''05'': 'Wide range' (Zyxel)| | detection_type | 1 | ''00'': No detection \\ ''01'': Legacy \\ ''02'': IEEE 802.3af 4-point detection (default) \\ ''03'': 4-point detection, followed by legacy \\ ''05'': 'Wide range' (Zyxel)|
 +
 +==== Set classification enable ====
 +  * ID: ''11''
 +  * Request: ''{ [port] [classification] }''
 +  * Reply: ''{ [port] [error] }''
 +
 +^ Field ^ Size ^ Description ^
 +| port | 1 | Port index number |
 +| classification | 1 | Automatic PD classification \\ ''00'': Disable \\ ''01'': Enable |
  
 ==== Set disconnect type ==== ==== Set disconnect type ====
Line 376: Line 386:
 | auto_powerup | 1 | | | auto_powerup | 1 | |
 | detection_type | 1 | Port detection type, see [[#Set detection type]] | | detection_type | 1 | Port detection type, see [[#Set detection type]] |
-| classification_enable | 1 | Enable PD classification |+| classification_enable | 1 | Enable PD classification, see [[#Set classification enable]] |
 | disconnect | 1 | Port disconnect type | | disconnect | 1 | Port disconnect type |
 | pair | 1 | Port power pair, see [[#Set port power pair]] | | pair | 1 | Port power pair, see [[#Set port power pair]] |
Line 455: Line 465:
   * ID: ''2b''   * ID: ''2b''
   * Request: (emtpy)   * Request: (emtpy)
-  * Reply: ''[ext_param_0] [pre_alloc] [powerup_mode] [ext_param_3] [ext_param_4] [ext_param_5] [num_pse] [ext_param_7] [ext_param_8]''+  * Reply: ''[ext_param_0] [pre_alloc] [powerup_mode] [disconnect] [ddflag] [ovlo] [num_pse] [ext_param_7] [ext_param_8]''
  
 ^ Field ^ Size ^ Description ^ ^ Field ^ Size ^ Description ^
-ext_param_0 | 1 | p0 from [[#Set device config]] |+uvlo | 1 | Under-voltage detection threshold, see [[#Set device config]] |
 | pre_alloc | 1 |  | | pre_alloc | 1 |  |
 | powerup_mode | 1 | | | powerup_mode | 1 | |
-ext_param_3 | 1 | Related to power management like pre_alloc, powerup_mode +disconnect | 1 | | 
-ext_param_4 | 1 | b1 from [[#Set device config]] | +ddflag | 1 | See [[#Set device config]] | 
-ext_param_5 | 1 | p2 from [[#Set device config]] |+ovlo | 1 | Over-voltage detection threshold, see [[#Set device config]] |
 | num_pse | 1 | Number of BCM59xxx PSE controllers present in the system | | num_pse | 1 | Number of BCM59xxx PSE controllers present in the system |
 | ext_param_7 | 1 | p3 from [[#Set device config]] | | ext_param_7 | 1 | p3 from [[#Set device config]] |
  • software/broadcom_poe_control_protocol.txt
  • Last modified: 2021/09/05 12:20
  • by svanheule